BioLight ReStore Full-Body Red Light Therapy Panel: Touch Screen, Adjustable Brightness & Pulsed Frequencies

BioLight ReStore Full-Body Red Light Therapy Panel: Touch Screen, Adjustable Brightness & Pulsed Frequencies

Name: BioLight ReStore Full-Body Red Light Therapy Panel: Touch Screen, Adjustable Brightness & Pulsed Frequencies
Brand: BioLight
SKU: RESTORE
Price: 1799.0 USD
Availability: InStock

by BioLight

$1,799.00 - $1,799.00

$1,799.00

$1,799.00 - $1,799.00

$1,799.00

✓ Authorized BioLight Dealer
✓ Lowest Price Guaranteed
✓ FREE & FAST Shipping: In Stock and Ready to Ship
✓ Questions? Call an RFA Team Member: 1-855-864-6442

BioLight | ReStore

BioLight ReStore Full-Body Panel

The ReStore is a 36 in. by 12 in. panel carrying 300 LEDs at 660nm red and 850nm near-infrared, and the control that separates it from a plain emitter is the pulse rate. Every LED can be switched on and off at a rate you set, anywhere up to 10,000 cycles per second, or left running continuously. That single control is what the touchscreen on the front is mostly there to reach.

BioLight quotes its output at 56.9 mW/cm2 at 6 in. at full brightness, and publishes the whole ladder underneath it: 56.5 mW/cm2 at 75%, 44 at 50%, 32 at 25% and 13 at 1%, all at the same 6 in. The panel is 3 in. deep, weighs 18 lbs, draws 476W through 8 cooling fans, and takes 100-240VAC at 50/60Hz. It ships with both a floor stand on wheels and a door hanging kit, which is the only device in BioLight's range that arrives with two mounting options in the same box.

Pulse rate set by hand Brightness 1 to 100% Floor stand and door hanger included 476W through 8 fans

BioLight ReStore full-body red light panel

The pulse control

What It Means to Pulse a Light Source

Most light panels run continuous wave: the diodes are on for the whole session. The ReStore can also run pulsed, switching every LED on and off at a rate you choose. Here is what that setting is, and what BioLight does and does not publish about it.

〰

Hertz Is a Count of On-Off Cycles

A pulsed emitter switches off and on again at a fixed rate, and the Hz figure counts how many of those cycles happen in one second. At 10 Hz an LED completes ten cycles a second. At 10,000 Hz a cycle lasts one ten-thousandth of a second, far too fast for an eye to resolve, so the panel looks steady while it is pulsing. Because the diode spends part of each cycle dark, a pulsed session puts less total energy on a surface than a continuous session of the same length at the same brightness. BioLight publishes the range and nothing beyond it: no preset modes and no recommended frequency. Their own page attaches an outcome claim to one specific frequency and names no author, journal, year or identifier for it, so that passage is not on this page.

Up to 10,000 cycles per second

💡

300 LEDs at 660nm and 850nm

Three hundred emitters across a 36 in. by 12 in. face, each behind a 30 degree focusing lens that narrows its output cone forward. BioLight calls the emitter their patent-pending Dual LED technology and describes each diode as capable of producing both wavelengths. That is BioLight's own description of their own component, and they publish no patent or application number alongside it.

30 degree focusing lens

📈

The Full Ladder at 6 Inches

BioLight publishes an irradiance figure for every brightness step, all measured at the same 6 in.: 56.9 mW/cm2 at 100% brightness, 56.5 at 75%, 44 at 50%, 32 at 25% and 13 at 1%. The distance is the part that makes the ladder readable, and BioLight quoting all five at 6 in. is what lets the five be compared with each other.

56.9 mW/cm2 at 6 in.

🌪

476W, 8 Fans, One Touchscreen

BioLight removed the physical buttons on this generation and put brightness, light setting, pulse rate and timer on a touchscreen. Behind it, 8 fans handle the heat of a 476W array, and the panel takes 100-240VAC at 50/60Hz so it runs on North American and international supply. Published light flicker is 1.2% modulation at 60Hz and LED lifespan is 100,000 hours.

8 cooling fans

The numbers

Eight Figures From BioLight's ReStore Specification

Every irradiance figure below is quoted at 6 in., the distance BioLight measured this panel at.

💡

300 LEDs

36 in. x 12 in. face

📈

56.9 mW/cm2 at 6 in.

100% brightness

🌈

660nm red, 850nm near-infrared

Three light settings

〰

Pulse rate up to 10,000 Hz

Or continuous

🎚

Brightness 1 to 100%

Five published steps

🔍

30 degree focusing lens

Beam angle per LED

🌪

476W through 8 fans

100-240VAC at 50/60Hz

🛡

18 lbs, 100,000 hour LEDs

3 year warranty, 60 day return

Closer look

The Face, the Screen and the Two Ways to Hang It

BioLight ReStore panel face with 300 LEDs

The panel

Three Hundred Emitters Across Three Feet

The ReStore's face is 36 in. tall and 12 in. wide on a 3 in. body, with 300 LEDs across it running 660nm red and 850nm near-infrared. Each LED sits behind a 30 degree focusing lens, which pushes more of its cone forward at whatever is in front of the panel and less of it out into the room. Three settings decide what comes out: both wavelengths together, red only, or near-infrared only. At 18 lbs the panel is light enough to move between the floor stand and the door hanger without help.

36 in. x 12 in. x 3 in., 18 lbs
300 LEDs at 660nm and 850nm
30 degree focusing lens on each LED
Three light settings: combined, red only, near-infrared only
56.9 mW/cm2 at 6 in. at 100% brightness

300 LEDs 36 in. face 18 lbs

BioLight ReStore touchscreen control panel

Controls

Four Settings Behind One Screen

BioLight took the physical buttons off this generation and put everything on a touchscreen: which of the three light settings runs, brightness anywhere from 1 to 100%, the pulse rate up to 10,000 Hz, and the timer. Brightness and pulse rate are independent, so a session can run bright and continuous, dim and continuous, or pulsed at any brightness. One note on BioLight's own numbers: they publish the pulsing floor two ways on the same page, as 0 Hz in the description text and 1 Hz in the specification block. The ceiling is 10,000 Hz in both places.

Touchscreen replaces the physical buttons
Brightness 1 to 100%, five published irradiance steps
Pulse rate up to 10,000 Hz, or continuous
Programmable timer, adjustable per session
Light flicker published at 1.2% modulation at 60Hz

Touchscreen 1-100% brightness To 10,000 Hz

BioLight ReStore panel on its wheeled floor stand

Mounting

A Stand and a Door Hanger, Both in the Box

The ReStore arrives with a floor stand on wheels and a door hanging kit, and you do not choose between them at purchase. The stand rolls the panel to wherever the session is happening and holds it upright; the door hanger puts it on the back of a door and gives the floor space back. BioLight publishes no wall mount for this model. The box also carries protective eyewear, the owner's manual and their Red Light Therapy Guide ebook, and the panel ships with a plug matched to the country on the shipping address.

Floor stand with wheels, included
Door hanging kit, also included
Protective eyewear
Owner's manual and The Red Light Therapy Guide ebook
Power plug matched to the shipping country

Stand included Door hanger included Eyewear included

Compare

Four BioLight Panels and Pods, Side by Side

The ReStore and the ReCharge are both quoted at 6 in., so their figures can be read against each other. The Cocoon is quoted at contact and the ReJuvenate carries two unreconciled values, so neither is set against the panels here.

You're Here

BioLight ReStore

A 36 in. by 12 in. full-body panel with 300 LEDs at 56.9 mW/cm2 at 6 in., shipping with both a floor stand and a door hanger.

300 LEDs 56.9 mW/cm2 at 6 in. Stand and door hanger 476W power draw

Currently viewing

BioLight ReJuvenate

BioLight's largest panel at 66 in. by 23 in., carrying 1008 LEDs, 20 cooling fans and a 3000W power draw.

1008 LEDs 66 in. tall panel 20 cooling fans 3000W power draw

Shop the BioLight ReJuvenate

BioLight Cocoon

A zip-around pod holding 3600 LEDs that opens flat into a 69 in. by 71 in. mat and weighs 17.4 lbs.

3600 LEDs 360 degree enclosure 5 intensity levels 17.4 lbs

Shop the BioLight Cocoon

BioLight ReCharge

The tabletop of the group at 11.3 in. by 8.3 in. and 8 lbs, with 60 LEDs rated 63 mW/cm2 at 6 in.

60 LEDs 63 mW/cm2 at 6 in. 8 lbs 136W power draw

Shop the BioLight ReCharge

Questions

Frequently Asked Questions

Up to 10,000 Hz. BioLight publishes the bottom of that range two different ways on the same page: the description text says 0 to 10,000 Hz and the specification block says 1 to 10,000 Hz. We have printed both figures because BioLight prints both, and we have asked them to confirm which is correct. The ceiling of 10,000 Hz is consistent everywhere on their page.

56.9 mW/cm2 at 6 in. at 100% brightness. BioLight publishes the full ladder at that same 6 in.: 56.5 mW/cm2 at 75%, 44 at 50%, 32 at 25% and 13 at 1%. No figure is published at any other distance, so 6 in. is the only measurement point for this panel.

No. A pulsed emitter is dark for part of every cycle, so over the same number of minutes at the same brightness setting a pulsed session puts less total energy on the surface than a continuous one. BioLight publishes their irradiance ladder against brightness only, so the figures above describe continuous output. They publish no derating table for pulsed operation.

BioLight publishes no recommended frequency and no preset modes for this panel, only the range. Their product page does attach an outcome claim to one particular frequency, with no author, journal, year or reference number behind it. We have left that passage off this page for exactly that reason, and we are not going to substitute a recommendation of our own.

660nm red and 850nm near-infrared, across all 300 LEDs, with three settings: both together, red only, or near-infrared only. Near-infrared at 850nm sits past the visible band, so the near-infrared-only setting looks close to dark while it is running.

BioLight's own name for the emitter in this panel, which they describe as patent-pending and as letting each individual LED produce both wavelengths. Two caveats, both about BioLight's page and neither about the hardware. The sentence they use to explain it on this product page contradicts itself; their clearer wording elsewhere describes each LED emitting red and near-infrared at the same time. And no patent number, application number or jurisdiction is published anywhere, so the patent-pending description is theirs, attributed to them, and not a claim we are making.

Two ways, and both parts are in the box: a floor stand with wheels and a door hanging kit. No choice is made at purchase and no upgrade is charged for either. BioLight publishes no wall mount for this model. At 18 lbs the panel moves between the two without help.

476W on 100-240VAC at 50/60Hz, which BioLight states covers both US and Canadian supply and international supply. Eight cooling fans move the heat off the array. LED lifespan is published at 100,000 hours.

Light flicker is given as 1.2% modulation at 60Hz. EMF emission is given as standard magnetic 0.3 mG, standard electric 30 V/m, weighted magnetic 0.3 mG, weighted electric 24 V/m and RF 0.15 mW/m2. BioLight publishes no measurement distance, laboratory name or report number alongside those EMF readings.

BioLight states 10 to 20 minutes per area, used 3 to 5 times per week, or daily during more intensive periods. That is BioLight's guidance, not ours. The programmable timer runs the clock so the panel shuts itself off.

The ReStore panel with a power plug matched to your shipping country, the door hanging kit, the floor stand, protective eyewear, the owner's manual and BioLight's Red Light Therapy Guide ebook.

BioLight publishes a 3 year warranty, a 60 day return period and a 100,000 hour LED lifespan. Orders ship direct from BioLight's manufacturer and they ask buyers to allow roughly 3 to 4 weeks for delivery.

The statements on this website have not been evaluated by the FDA (U.S. Food & Drug Administration). Our products are not intended to diagnose, treat, cure, or prevent any disease.

Wavelengths: 660nm red and 850nm near-infrared
LED count: 300 LEDs
Irradiance (all at 6 in.): 56.9 mW/cm2 at 100% brightness; 56.5 at 75%; 44 at 50%; 32 at 25%; 13 at 1%
Light pulsing: Up to 10,000 Hz. BioLight publishes the floor two ways on the same page: 0 Hz in the description and 1 Hz in the specification block
Brightness: 1-100%, adjustable
Light settings: Red and near-infrared combined, red only, near-infrared only
Beam angle: 30 degree focusing lens
Dimensions: 36 in. x 12 in. x 3 in.
Weight: 18 lbs
Power: 476W
Electrical input: 100-240VAC 50/60Hz
Cooling fans: 8
Controls: Touchscreen with programmable timer
Light flicker: 1.2% modulation at 60Hz
EMF emission: Standard magnetic 0.3 mG, standard electric 30 V/m, weighted magnetic 0.3 mG, weighted electric 24 V/m, RF 0.15 mW/m2
Mounting: Floor stand with wheels and door hanging kit, both included
LED lifespan: 100,000 hours
Warranty: 3 years
Return period: 60 days
Session time: 10-20 minutes per area
Lead time: Approximately 3-4 weeks, ships from BioLight's manufacturer

300 LEDs: 36 in. x 12 in. face
56.9 mW/cm2 at 6 in.: 100% brightness
660nm red, 850nm near-infrared: Three light settings
Pulse rate up to 10,000 Hz: Or continuous
Brightness 1 to 100%: Five published steps
30 degree focusing lens: Beam angle per LED
476W through 8 fans: 100-240VAC at 50/60Hz
18 lbs, 100,000 hour LEDs: 3 year warranty, 60 day return

ReStore panel: With a power plug matched to the shipping country
Door hanging kit: Included
Floor stand: With wheels, included
Protective eyewear: Included
Owner's manual: Included
The Red Light Therapy Guide ebook: Included